CLICK HERE TO BUY!

Sears Craftsman Belt Drive Contractor Style Table Saw Motor. This is a 1 1/2HP motor that Sears marketed as a "3HP MAX" motor.

This motor came on a 10" contractor saw but is well configured to be used as a universal replacement motor. It has a standard 56 frame and a 5/8" keyed output shaft. 110V power cord is included.

This motor clean, quiet, and in excellent condition.

1 1/2 HP  3450… Continue reading

CLICK HERE TO BUY!

Delta 34-806  10 inch table saw with Biesemeyer fence

CLICK HERE TO BUY!

LISTED IS A  DREMEL 580 TABLESAW IN VERY NICE CONDITION,NO RUST,NOT BEAT UP,RUNS GREAT AND ALL MOVING PARTS ARE LUBRICATED AND OPERATE WITH EASE,IT IS SET UP ON A BASE AND BACK DUST PLATE TO PREVENT A SAW DUST MESS WHEN USING ,JUST HOOK UP TO A SMALL SHOP VAC. SAW WILL TILT ON BASE FOR SERVICE,IT NEEDS NOTHING,JUST INSTALLED NEW HEAVY DUTY BELT,THE BLADE GUARD HAD A… Continue reading

CLICK HERE TO BUY!

LISTED IS A VERY NICE PROXXON FKSE VARIABLE SPEED TABLESAW WITH EXTRAS,THIS IS ONE OF THOSE TWO OR THREE PROJECT SAWS THAT SHOWS VERY,VERY MINIMAL USE,THE BLADE GUARD IS STILL SHINY& NOT EVEN SCRATCHED,IT COMES WITH ALL FACTORY ACCESSORIES PLUS A NICE CUSTOM MADE DROP IN EXTENSION TABLE ,EXTRA NEW CARBIDE BLADE,THREE BLANK BLADE PLATES,OWNERS MANUAL,TWO RIP FENCES,ONE WITH HIGH RIP GUIDE BAR,MITER GAUGE,ALLEN WRENCHES ETC.ALL ITEMS PICTURED WILL BE… Continue reading

CLICK HERE TO BUY!

Powermatic Model 64A 10" contractors table saw with 52" Accu-Fence and left-tilt blade.  115/230V 1-1/2 HP, single phase 60 Hz motor, currently wired for 230V.  Includes side out-feed table, under-table storage, 3 blades (1 Forrest Woodworker II 40T combo, 1 Freud 40T combo, and generic combo), splitter/blade guard, and owner's manuals.  Also comes with many shop-made fixtures (cross-cut sled, etc.) that are not included in… Continue reading

CLICK HERE TO BUY!

SHOPSMITH HEADSTOCK WITH A 1 1/8 h.p. A.O. SMITH MOTOR. THIS IS A NICE HEADSTOCK. I PUT A DAB OF LITIUM GREASE ON THE SPEED CHANGER GEARS. GOES THROUGH ALL THE SPEEDS WITH EASE. LUBRICATED BOTH UPPER & LOWER SHEAVES "THIS IS WHERE THE DRIVE BELT RIDES ON DURING OPERATION AND THEY NEED TO GO OUT AND IN WITH EASE". CLEANED RE-WAXED AND ADJUSTED THE… Continue reading

CLICK HERE TO BUY!

 For sale is a used Biesemeyer table saw fence.     It's in good condition with the exception of having a minor saw blade gouge, but is still very usable.     The Formica cover could easily be replaced on that side or covered with another piece of Formica if you didn't like it the way it is.    This auction is for the fence only - no table guide… Continue reading

CLICK HERE TO BUY!

Craftsman 10" x 27" Cast Iron Router Table Extension Wing.

Mounting holes are at 1 1/8",  9 3/8", 17 5/8" and 25 7/8" from the end. There is a rail mounting fastener hole centered on each end.

Router opening inner diameter is 62mm and outer diameter is 65mm. A set of 5 router inserts is included. The two sets of mounting holes will fit most Craftsman routers router models. Wing… Continue reading

CLICK HERE TO BUY!

Sears Craftsman Belt Drive Contractor Style Table Saw Motor. This is a 1 1/2HP motor that Sears marketed as a "3HP MAX" motor.

This motor came on a 10" contractor saw but is well configured to be used as a universal replacement motor. It has a standard 56 frame and a 5/8" keyed output shaft. 110V power cord is included.

This is a very low hour motor that is clean and… Continue reading

CLICK HERE TO BUY!

UP FOR AUCTION: DEWALT DW745 10-INCH COMPACT JOB SITE TABLE SAW 

GENERAL CONDITION: PRE-OWNED IN GOOD CONDITION.

LOCAL PICK UP ONLY!! ZIP CODE: 23704

WORKING CONDITION: GOOD - TESTED AND WORKS FINE

COSMETIC… Continue reading

 Page 1 of 317  1  2  3  4  5 » ...  Last »